 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SP0102BE3 "Zero Height" SiSonicTM Microphone Specification Knowles Acoustics 1151 Maplewood Drive Itasca, IL 60143 Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 1 of 10 SP0102BE3 1. DESCRIPTION AND APPLICATION 1.1 Description Zero Height Surface Mount Silicon Microphone 1.2 Application Hand held telecommunication devices 2. PART MARKING Identification Number Convention S Identification Number 4 1 5 2 6 3 S: Manufacturing Location "S" - Knowles Electronics Suzhou Suzhou, China "No Alpha Character" - Knowles Electronics Itasca Itasca, IL USA Pin 1 "E" - Engineering Samples Digits 1 - 6: Job Identification Number 3. TEMPERATURE RANGE 3.1 Operating Temperature Range: -40C to +100C 3.2 Storage Temperature Range: -40C to +100C Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 2 of 10 SP0102BE3 4. ACOUSTIC & ELECTRICAL SPECIFICATIONS Limits Symbol Condition Min. Nom. Max. Unit Directivity Sensitivity Output impedance Current Consumption Signal to Noise Ratio Supply Voltage Typical Input Referred Noise Sensitivity Loss across Voltage Maximum Input Sound Level Contact Resistance S ZOUT IDSS S/N Vs ENL Omni-directional @ 1kHz (0dB=1V/Pa) @ 1kHz (0dB=1V/Pa) across 1.5 to 5.5 volts @ 1kHz (0dB=1V/Pa) -46 n/a 0.100 55 1.5 A-weighted Change in sensitivity over 5.5v to 1.5v n/a -42 n/a n/a 59 n/a 35 -38 100 0.250 n/a 5.5 n/a dB mA dB V dBA SPL No Change Across Voltage Range dB dB At 100dB SPL, THD < 1% At 115dB SPL, THD = < 10% 100 Ohms 5. FREQUENCY RESPONSE CURVE Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 3 of 10 SP0102BE3 6. MECHANICAL SPECIFICATIONS Item Dim. Tol. (+/-) +0.20 -0.10 0.10 0.10 Units Height Length Width Weight Coplanarity 1.65 6.15 3.76 0.09 < 0.1 mm mm mm grams mm Side View Top View Pin Output Pin # 1 2 3 4 Function Output Ground Ground Power Bottom View (Note: Tolerance +/-0.15mm unless otherwise specified) Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 4 of 10 SP0102BE3 7. RECOMMENDED CUSTOMER LAND PATTERN * * Note: Minimum PCB Hole Diameter: 1.02 mm Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 5 of 10 SP0102BE3 8. RECOMMENDED SOLDER STENCIL PATTERN Notes: * * * The design requires that an acoustic seal be established between the SiSonic and customer PCB. This is accomplished via a solder seal. Solder Stencil Thickness = 0.127 min to 0.178 max Stencil Material = Stainless Steel Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 6 of 10 SP0102BE3 9. RECOMMENDED INTERFACE CIRCUIT Dotted Section Represents SiSonic Microphone + Term. 4 * R2 R1 * * Term. 3 Term. 2 Term. 1 + Vref External Gain (set by customer) = -R1/R2 10. PACKAGING DETAIL Pin 1 Location Tape & Reel Available in 13" and 7" diameter. 800mm or minimum of 100 empty pockets Label applied to external package and direct to reel. Per JEDEC. No consecutive empty pockets; No more than 3 empty pockets per reel. (Does not include empty pockets for leader/follower) Model Number SP0102BE3 SP0102BE3 Suffix -5 -4 Reel Diameter 7" 13" Qty per Reel 900 3,600 Leader Length Label Empty Units Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 7 of 10 SP0102BE3 11. SOLDER REFLOW PROFILE Notes: 1. Maximum condition = 260 C for 30 seconds. 2. Do not pull a vacuum over the port hole of the microphone. Pulling a vacuum over the port hole can damage the device. 3. Do not board wash after the reflow process. Board washing and cleaning agents can damage the device. Do not expose to ultrasonic processing or cleaning. 4. Number of Reflow = recommend no more than 2 cycles. 12. ADDITIONAL NOTES (A) (B) (C) Packaging (reference SiSonic_Packaging_Spec.pdf) Shelf life: Twelve (12) months when devices are to be stored in factory supplied, unopened moisture sensitivity bag under environmental conditions of 30C, 60% R.H. Exposure: Devices should not be exposed to high humidity, high temperature environment. Customer should follow standard baking times as stated in JEDEC J-STD -033A, reference Class 2A. Out of bag: 90 days out of ESD moisture sensitive bag, assuming 30C/60% RH as maximum. Baking Condition: After 90 days, refer to JEDEC J-STD-033A for recommend baking times and temperatures, Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 8 of 10 SP0102BE3 13. RELIABILITY SPECIFICATIONS Note: After test conditions are performed, the sensitivity of the microphone shall not deviate more than 3dB from its initial value. Test Thermal Shock Description Microphone unit must operate when exposed to air-to-air thermal shock 100 cycles, from -40C to +125C. (IEC 68-2-4), Microphone unit must maintain sensitivity after storage at +105C for 1,000 hours. (IEC 68-2-2 Test Ba) Microphone unit must maintain sensitivity after storage at -40C for 1,000 hours. (IEC 68-2-1 Test Aa) Microphone unit must operate within sensitivity specifications for 1,000 hours at 105C. (IEC 68-2-2 Test Ba) High Temperature Storage Test Low Temperature Storage Test High Temperature Operating Test Low Temperature Operating Test Humidity Test Vibration Test Microphone unit must operate within sensitivity specifications for 1,000 hours at -40C. (IEC 68-2-1 Test Aa) Tested under Bias at 85C/85% R.H. for 1,000 hours. (JESD22-A101A-B) Microphone unit must operate under test condition: 4 cycles, from 20 to 2,000 Hz in each direction (x,y,z), 48 minutes, using peak acceleration of 20 G (+20%, -0%). (MIL 883E, method 2007.2, A) Tested to 8kV direct contact discharge or 15kV air discharge as specified by IEC 10004-2, level 3 and level 4. Microphone is tested to 5 passes through reflow oven, with microphone mounted upside-down under conditions of 260C for 30 seconds maximum. Microphone must operate after exposure to shock test of 10,000 G per IEC 68-2-27, Ea. Electrostatic Discharge Reflow Mechanical Shock Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 9 of 10 SP0102BE3 14. SPECIFICATION REVISIONS Revision A Detailed Specification Changes Initial Release Date 12-1-04 Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 10 of 10 |
Price & Availability of SP0102BE3
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |